Meters to Feet Converter

Meters to feet: the quick answer

To convert meters to feet, multiply the length in meters by 3.28084. So the formula is feet = meters × 3.28084. As quick anchors, 1 meter equals about 3.28 feet, 2 meters to feet is 6.56 feet, and 3 meters to feet is 9.84 feet. This meters to feet converter applies that factor instantly as you type, but the rule is simple enough to do on paper once you remember the "times 3.28" pattern.

The meter is the base unit of length in the metric system, used almost everywhere outside the United States. The foot is the everyday unit of length in the US and is still common in the UK for height and some construction. Because the two come from different measurement systems, you cannot just swap the number; you have to scale it by a fixed factor. That is why a reliable converter of meters to feet is so useful for height, travel, sports, real estate, and reading any spec or plan written in the other system. To go the other way, this same tool works as a feet to meters converter too.

The exact relationship is fixed by definition: one foot is exactly 0.3048 meters. Flip that around and one meter is 1 ÷ 0.3048 = 3.280839895 feet, which most people round to 3.28084. Because the link is a single fixed multiplier with no offset, the math is cleaner than temperature: there is nothing to add or subtract, just one multiplication. That makes the meters converter to feet a fast mental estimate as well as a precise tool, since "about three and a quarter feet per meter" gets you close in your head.

How to use the meters to feet converter

The tool is free, browser-based, and needs no signup. To convert a length:

1. Type the length in meters into the input field. Decimals such as 1.75 are fine.
2. Read the result in feet, which updates instantly as you type.
3. For height, note the whole feet and convert the leftover decimal to inches (see the formula section below).
4. Switch the direction when you need feet to meters instead.
5. Copy the figure or jot down the rounded value.

Because the same converter for meters to feet runs both directions, you can double-check any result by converting it back. Enter a value in meters, note the feet, then convert that figure back and confirm you land on the original. The result recalculates with every keystroke, so you can sweep through a range, say 1.6, 1.7, 1.8 m, and watch the feet climb, which is handy when comparing heights or sizing a room.

Meters to feet formula and worked example

There is no offset, only a scale factor, so the conversion is a single multiplication:

feet = meters × 3.28084

For a worked example, convert 1.8 meters, a common adult height. Multiply 1.8 × 3.28084 to get 5.91 feet. To express that in feet and inches, keep the whole 5 feet and multiply the 0.91 remainder by 12 to get about 11 inches, so 1.8 m is roughly 5 feet 11 inches. To reverse the process, divide feet by 3.28084 (or multiply by 0.3048): 5.91 ÷ 3.28084 returns 1.8 m. That reverse rule, meters = feet × 0.3048, is the whole of the converter feet to meters method. The table below covers the lengths people convert most.

Common meters to feet conversions and use cases

Most lookups are heights, room dimensions, and short distances. This reference covers the values people search for most, including the popular 2 meters to feet, 3 meters to feet, and 4 meters to feet queries, plus the meters to feet and inches breakdown for height.

The conversion turns up in plenty of everyday settings, and the precision you need depends on the job:

• Height. Comparing a height given in meters with the feet-and-inches scale people use in the US is the single most common reason to convert. Round to the nearest inch and you are done.
• Real estate and rooms. Floor plans and ceiling heights often list meters. A 2.4 m ceiling is about 7 ft 10 in, which tells you instantly whether a tall wardrobe will fit.
• Sports and water. Pool depths, diving heights, and field markings cross between systems. A 3-metre board sits at 9.84 feet above the water.
• Travel and signage. Trail markers, bridge clearances, and building heights abroad are usually metric, so a fast meters converter to feet helps you picture the scale.

Square meters to square feet (a different conversion)

Area is not the same as length, so do not use 3.28084 for it. Because area scales with the square of the length factor, one square meter equals 3.28084², which is 10.7639 square feet. The formula is square feet = square meters × 10.7639. A 20 m² room is therefore about 215 square feet. If you are working with floor area or land, use a dedicated square feet to square meters converter or square meters to square feet converter rather than the linear factor, since squaring the wrong number is the most common area-conversion mistake.

Common mistakes when converting meters to feet

• Using a rounded 3.3 for precise work. 3.28084 is the accurate factor. Using 3.3 inflates a 10 m measurement by nearly two inches.
• Treating the decimal feet as inches. 5.91 feet is not 5 feet 91 inches. Multiply the 0.91 decimal by 12 to get the inches: about 11.
• Mixing up length and area. Meters to feet uses 3.28084; square meters to feet uses 10.7639. They are not interchangeable.
• Inverting the direction. Meters to feet multiplies by 3.28084; feet to meters multiplies by 0.3048. Swapping them gives a wildly wrong answer.
• Rounding too early. Convert first, round last. Rounding mid-calculation, especially on longer distances, compounds the error.

Tips and related converters

The two facts worth memorising are the factor (one meter is about 3.28 feet) and the inch step (multiply the leftover decimal by 12). With those you can sanity-check any reading, then rely on this meters to feet converter for the exact decimal. For height especially, the feet-and-inches breakdown is what most people actually want, so convert the decimal remainder rather than reading it as inches directly.

It also helps to carry a couple of reference points. A standard interior door is about 2 m, or 6 ft 7 in; a typical adult is between 1.6 and 1.9 m, which is roughly 5 ft 3 in to 6 ft 3 in. When a converted value lands far from these familiar markers, it is usually a sign you used the area factor by mistake or inverted the direction. A quick comparison against a length you already know catches most slips before they matter.

Working in the other direction or with area? Reverse the conversion with the Feet to Meters Converter, handle floor and land area with the Square Feet to Square Meters Converter or the Square Meters to Square Feet Converter, and convert plots given in yards with the Square Yards to Square Meters Converter. All of these live in the Unit Converters hub.

Frequently asked questions

What is the formula to convert meters to feet? Multiply the length in meters by 3.28084: feet = meters × 3.28084. One foot is defined as exactly 0.3048 meters.

What is 2 meters to feet? 2 meters equals about 6.56 feet, or 6 feet 7 inches, because 2 × 3.28084 = 6.56.

What is 3 meters to feet? 3 meters equals about 9.84 feet, since 3 × 3.28084 = 9.84.

What is 4 meters to feet? 4 meters equals about 13.12 feet, because 4 × 3.28084 = 13.12.

How do I convert meters to feet and inches? Convert to feet first, then multiply the decimal part by 12 to get the inches. For 1.8 m: 1.8 × 3.28084 = 5.91 ft, and 0.91 × 12 ≈ 11 in, so 5 feet 11 inches.

How do I convert feet back to meters? Multiply the feet value by 0.3048, or divide by 3.28084. For example, 6 feet × 0.3048 = 1.83 m.

How do I convert square meters to square feet? Multiply by 10.7639, not 3.28084, because area scales with the square of the length factor. A 50 m² space is about 538 square feet.

Why are meters and feet different? They belong to different measurement systems, the metric and the imperial, so converting between them requires a fixed scale factor of 3.28084.